Which way should deck joists run?
Construction begins like a standard deck, with ledger board fastened to the house and joists running perpendicular. Each joist is routed on the sides every 16 inches on center, 1/16″ deep in the shape of a 2×4.
How do I square my first deck board?
Mark the first few deck boards with a carpenter’s pencil run along the carpenter’s square as it crosses the deck board ends. Snap a chalk line to continue the pencil mark along the entire deck. Cut the deck boards square with a circular saw.
Are deck boards actually 6 inches wide?
The most common or standard deck board width is 6-inch wide planks based on square-foot coverage, labor, and material cost.
How wide is a 2×6 deck board?
2×6 Decking is Thicker Than 5/4 Both with a deceptively different material thickness. 2×6 Deck Boards actual Dimensions 1.5″ x5. 5.” 5/4 Decking Actual Dimensions 1″ x 5.5.”
What is the actual width of a 5 4 deck board?
5/4 Decking Actual Dimensions 1″ x 5.5.” If you use 5/4 decking, you are getting two-thirds of the board of a 2×6. Like getting a Big Mac without the middle bun, still decking just less. There are some trades off with this difference. Some are positive, and some are not.
How do you start the first deck board?
In most cases, it’s best to start with a full board on the outside edge of the deck and work toward the house so the odd board is less visible. Then measure when you’re 4 to 5 ft. away from the house and adjust the gap sizes to be sure the last board is a consistent width.
What is a 5 4 inch board?
It simply refers to how many 1/4-inches thick the rough stock is. For example, 4/4 (read out loud as four-quarters) is 1-in. thick in the rough. 5/4 is 1-1/4-in. thick, 12/4 would be three inches thick.15 Jun 2021
What is the actual thickness of a 5 4 board?
1.25″ thick
How do I make sure the first deck board is straight?
What is the actual size of a 1×6 deck board?
A 1×6, for example, actually measures 3/4″ x 5 1/2″. In this case, the planing is necessary for a smoother surface, so that the board could be used for interior applications. The length of the boards is generally exactly what you order, though we usually only stock pieces of even lengths.
How do I make sure deck boards are square?
To keep your framing square while you install your decking, screw a long, 1-by-4-inch piece of lumber under the joists on a diagonal, ideally parallel to the 5-foot distance in the 3-4-5- method. Keep this 1-by-4 in place as you attach the decking.
How do you square a deck board?
Where do you start deck boards?
Deck boards should sit 1 ½” off the edge of each side of your deck. Use your straightest deck board and lay it first across the deck’s front edge, opposite your house. Each board should have a ⅛” gap. All deck board should end on a joist, making sure to stagger deck board ends.
How do you start laying decking?
Should decking be parallel to house?
The default direction decking runs on an attached deck is parallel with the house. A few reasons for this are deck framing construction, water runoff and appearance. Decking running parallel to the house is beneficial structurally, aesthetically and costwise.
Are decks supposed to slope away from house?
How Much Should a Deck Slope Away from the House? A deck should slope ⅛” per foot perpendicular from a house. Regardless of deck orientation which direction the deck boards run a minimum slope of ⅛” is optimal for shedding water. If your deck surface is solid, then ¼” per foot is a better choice.
How thick is a standard board?
In modern lumber practices, the boards are no longer exactly 2 x 4 inches when first cut, but today’s drying and planing methods still leave the board 1 1/2 inches thick and 3 1/2 inches wide.27 Mar 2020
Used Resourses:
- https://www.youtube.com/watch?v=m6E_c8wPMUU
- https://decksbye3.com/comparing-5-4-decking-with-2×6-deck-boards-pros-and-cons/
- https://www.thesprucecrafts.com/understanding-wood-sizes-in-softwood-lumber-3536905
- https://www.newtechwood.com/blog/how-to-keep-deck-boards-straight/
- https://www.oneprojectcloser.com/run-decking-boards-parallel-to-the-joists-perpendicular-to-the-house/
- https://decksbye3.com/comparing-5-4-decking-with-2×6-deck-boards-pros-and-cons/
- https://howelumber.com/dimensional-lumber
- https://plasticinehouse.com/how-to-lay-deck-boards/
- https://plasticinehouse.com/deck-board-dimensions/
- https://www.decks.com/how-to/articles/framing-a-deck-parallel-to-a-house
- https://www.kencraftcompany.com/terminology/
- https://plasticinehouse.com/should-deck-have-slope/
- https://homeguides.sfgate.com/keep-deck-boards-square-24523.html
- https://www.youtube.com/watch?v=wYjsAD1tHns
- https://www.homedepot.com/p/WeatherShield-5-4-in-x-6-in-x-16-ft-Standard-Pressure-Treated-Decking-Board-128966/100073603
- https://decksbye3.com/running-decking-parallel-is-common-but-not-the-only-option/
- https://www.oneprojectcloser.com/run-decking-boards-parallel-to-the-joists-perpendicular-to-the-house/
- https://www.rockler.com/learn/what-does-quarter-system-of-lumber-thickness-mean
- https://www.youtube.com/watch?v=NadW7SQlnvo
- https://www.familyhandyman.com/project/set-and-nail-decking-perfectly/
